BetaFPV F4 2-3S 20A AIO Flight Controller V1

$55.00 USD

CURRENTLY IN STOCK

Out of stock
Order in H, M, Seconds (before 1pm AEST) for same day despatch
Add to Wishlist
SKU: 28459N/A W/H: T-05-C-01 N/A Barcode: N/A Shipping Weight: 0g N/A Categories: AIO , BetaFPV , BetaFPV FC , FPV Stack Combos , Tinywhoop Flight Controller Tags: AIO, BetaFPV, Flight Controller, FPV Stack Combos, Tinywhoop Flight Controller

We accept the following payment methods

Are you looking to buy a BetaFPV F4 2-3S 20A AIO Flight Controller V1 in Australia?

F4 2-3S 20A AIO FC V1 is specifically designed for HD VTX, utilizing 2-3S batteries for enhancing the flight experience. It features a dual BEC solution that delivers stable power outputs of 9V@2A for DJI O3 and 5V@3A for external devices. With a 20A ESC, it enables agile flight and increases dynamic. And connector for DJI O3 HD VTX and USB port for easy installation and maintenance. Ideal for HD VTX whoop enthusiasts, offering a heightened level of professionalism and convenience with this FC option.F4 2-3S 20A AIO FC V1

Features

  • Designed for HD VTX, it features a dual 9V@2A for DJI O3 and 5V@3A for external device BEC solution to prevent screen blackout on the DJI O3 due to low voltage during throttle increase.
  • It includes a new DJI O3 6-pin PMU for easy installation without soldering, reducing assembly complexity. Newbie friendly.
  • The power range of 2-3S provides increased thrust and improved control with a 20A ESC featuring a single NMOS for continuous current capability.
  • The upgraded onboard receiver allows selective power cutoff for saving power and offers additional UART TX3 and RX3 ports for connecting the external device.
  • Redesigned solder pad layout ensures larger, more secure pads for easy and reliable soldering, while the relocated USB port at the rear facilitates computer tuning.
  • It features an STM32F405RGT6 chip, Integrate Serial ELRS 2.4G receiver, 16M black box, barometer, current meter, reserve 3 complete serial ports and a standard SBUS, support GPS, HD VTX, external receiver, and other equipment.

Specifications

  • Weight: 5.58g (without motor connectors and power cable),5.92g (with motor connectors)
  • Mounting Hole Size: 26mm x 26mm
  • CPU*: STM32F405RGT6 (168MHz)
  • Six-Axis: ICM42688P (SPI connection)
  • RX: Serial ELRS 2.4G Receiver
  • RX firmware version: BETAFPV AIO 2400 RX ELRS V2.5.2
  • Antenna: Enameled wire
  • Blackbox Memory: 16MB
  • Sensor: Barometer(BMP280),  Voltage&Current
  • 5V BEC*: 5V 3A@8V supply
  • 9V BEC*: 9V 2A@8V supply
  • USB Port: SH1.0 4-Pin
  • Built-in ESC with 20A continuous and peak 25A current
  • ESC input voltage: 2-3S
  • FC firmfware version: Betaflight_4.4.1_BETAFPVF405
  • ESC firmware: C_X_70_48_V0.19.2.hex for BB51 Bluejay hardware
  • Signal support: D-shot300, D-shot600

*The output current of BEC will decrease as the temperature increases

Diagram

F4 2-3S 20A AIO FC V1F4 2-3S 20A AIO FC V1

Comparison

We upgraded the FC from F4 1S 12A AIO FC V3 to F4 2-3S 20A AIO FC V1. The upgraded FC features an ESC with a pulse overcurrent capacity of 25A, ensuring stable operation of the flight controller even in the event of motor stalling. The addition of a 9V 2A BEC power supply ensures the stable operation of the DJI O3 HD VTX when the battery voltage is low. It also includes a DJI O3 6-pin PMU allowing for connection to HD VTX without soldering. It integrates features such as a 16MB black box, with support for GPS, external receivers, and other devices. The redesigned solder pad layout and USB connector make installation and maintenance easier and more convenient.

F4 1S 12A AIO FC V3 F4 2-3S 20A AIO FC V1
Weight 4.23g 5.58g
BEC 5V@3A for External RX

5V@3A for External RX

9V@2A for DJI O3

Connector for DJI O3 Not support Support
ESC Current 12A 20A
ESC Input Voltage 1-2S 2-3S
Number of Serial Ports 2*UART, 1*SBUS 4*UART, 1*SBUS

Note: If you use the F4 2-3S 20A AIO FC V1, the serial port of the SBUS receiver is UART5 while F4 1S 12A AIO Brushless FC V3 is UART6.

F4 2-3S 20A AIO FC V1 also has extended the USB port to the end for easier parameter adjustment and wiring. And a new DJI O3 6-pin PMU has been added for convenient installation and maintenance.

FAQ

Power cutoff: Removing the chip bead disconnects the power supply, and to reuse the onboard ELRS receiver, soldering the solder pads together restores power.

UART3 release: Removing two resistors on the solder pads releases UART3. The left side is TX3, and the right side is RX3. To reconnect, solder the solder pads together when reusing the onboard ELRS receiver.

F4 2-3S 20A AIO FC V1

Voltage Switch: The HD VTX connector defaults to 9V. The chip bead is soldered between the 9V pad and the middle pad. To use WalkSnail Avatar HD mini 1s and Lite, please ensure the power supply voltage is 5V. Remove the chip bead first from the 9V pad and solder it between the middle pad and the 5V pad. Alternatively, you can use solder instead the chip bead to switch between the 5V and 9V pads.

F4 2-3S 20A AIO FC V1

Betaflight Firmware and CLI

FC firmware: Betaflight_4.4.1_BETAFVF405 

Download the firmware and CLI dump file

Reference link:

https://github.com/betaflight/betaflight/releases/tag/4.4.1 

ESC Firmware

With BB51 ESC solution, F4 2-3S 20A AIO FC V1 is based on BLHeliSuite16714903 with Bluejay ESC firmware, it supports bidirectional D-shot and RPM filtering in Betaflight, offers 24KHz, 48KHz, and 96KHz fixed PWM frequency for options, and custom start-up melodies. F4 2-3S 20A AIO FC V1 default factory setting is 48KHz and it doesn’t recommend upgrading the 96KHz, or it might cause an error in the motor idle setting, not spinning when disarmed.

DO NOT flash the firmware with a shorter interval, otherwise, there will be a certain chance of stalling and burning the flight controller.

Serial ELRS 2.4G RX

Serial ELRS 2.4G RX uses the Crossfire serial protocol (CRSF protocol) to communicate between the receiver and the flight controller board. So the Serial ELRS 2.4G RX is available to support upgrading to ELRS V3 with no need to flash Betaflight flight controller firmware. 

  • Enter binding status by power on/off three times.
  • Plugin and unplug the flight controller three times;
  • Make sure the RX LED is doing a quick double blink, which indicates the receiver is in bind mode;
  • Make sure the RF TX module or radio transmitter enters binding status, which sends out a binding pulse;
  • If the receiver has a solid light, it's bound.

The Serial ELRS 2.4G RX can be updated via Wi-Fi or Betaflight serial passthrough. Here is the way to update the Serial ELRS 2.4G RX firmware through passthrough.

  • Plug in your FC to your computer, but do NOT connect to betaflight configurator.
  • Choose target "BETAFPV 2.4GHz AIO RX". 
  • Flash using the BetaflightPassthrough option in ExpressLRS Configurator.

Connecting External Devices

Please note that the board reserves two serial ports and a standard SBUS port, which is available for the external CRSF protocol receiver or GPS module, and SBUS protocol receiver. You can refer to the below picture.F4 2-3S 20A AIO FC V1

Included

  • 1 * F4 2-3S 20A AIO FC V1
  • 4 * M2*10 Machine Screw 
  • 4 * M2*10 Nylon Screw 
  • 4 * M2 Nuts 
  • 4 * Shock Absorbing Ball 
  • 4 * JST1.25mm Angle Socket 
  • 4 * JST1.25mm Straight Socket 
  • 1 * SH1.0 4Pin Adapter Cable
  • 1 * Type-C to SH1.0 Adapter 
  • 1 * XT30 Power Cord
  • 1 * Filter Capacitor 
  • 1 * 30mm Double-head VTX connector wire 
  • 1 * 60mm Single-head VTX connector wire

Browse more

Betafpv Customized Parts – BETAFPV Hobby

Why Choose Phaser FPV?

Here’s Why 1000s of Buyers Trust Us

In the sky-high world of FPV drones and related products, Phaser FPV takes you higher and further – while ensuring a smooth ride every step of the way. As a human brand that puts its clients first, here are a few of the ways we keep giving our customers reasons to come back.

Same-Day Ship

If you place your order with us before 1pm weekdays, we’ll ship it out on the same day you shopped. When we make a promise, we keep it. You’ll be hard-pressed to find any Phaser order that didn’t fly out of our facility on the day it was ordered.


Transparent Stock

We keep our website updated like hawks. If you see it and it says it’s in stock, you can order it today and get it tomorrow via express shipping.

Highly Rated

We’ve spent almost a decade racking in countless 5-star reviews. Give them a read and you'll see everything we have said here is true!

Walk In Anytime

Can’t wait? Then don’t. We’re one of the only FPV drone + accessory stores to have a physical brick-and-mortar establishment in Somersby NSW Australia.

Fast Support

We welcome our customers to reach out to us via email, phone, or LIVE chat. Phaser FPV is the only FPV business to have a dedicated phone line.

We’re on Social

We have nothing to hide. Follow us on social, tag @PhaserFPV, and become a part of our online community and family in our facebook group.

It’s clear to see why most of our business comes through word-of-mouth referrals. When you need the best in FPV & 3D Printing don’t settle for less. Demand the best – insist on Phaser FPV.

Sunday,Monday,Tuesday,Wednesday,Thursday,Friday,Saturday
January,February,March,April,May,June,July,August,September,October,November,December
Not enough items available. Only [max] left.
Shopping cart

Your cart is empty.

Return To Shop

Add Order Note Edit Order Note
Estimate Shipping
Add A Coupon

Estimate Shipping

Add A Coupon

Coupon code will work on checkout page

BetaFPV F4 2-3S 20A AIO Flight Controller V1

$55.00