Are You Looking For SpeedyBee F405 50A 30x30 FC&ESC Stack In Australia?
Specifications
SpeedyBee F405 V3 30x30 Flight Controller
- MCU: STM32F405
- IMU(Gyro): BMI270
- USB Port Type: Type-C
- Barometer: Built-in
- OSD Chip: AT7456E chip
- BLE Bluetooth: Supported. Used for Flight Controller configuration
- DJI Air Unit Connection Way: Two ways supported: 6-pin connector or direct soldering.
- Blackbox MicroSD Card Slot: Betaflight firmware requires the type of the microSD card to be either Standard (SDSC) or High capacity (SDHC), so extended capacity cards (SDXC) are not supported(Many high-speed U3 cards are SDXC). Also the card MUST be formatted with the FAT16 or FAT32 (recommended) filesystems. So, you could use any SD card less than 32GB, but the Betaflight can only recognize 4GB maximum. We suggest you use this 3rd party formatting tool and choose 'Overwrite format' then format your card. Also check out here for the recommended SD cards or buy the tested cards from our store.
- BetaFlight Camera Control Pad: Yes(CC pad on the front side)
- Current Sensor Input: Supported. For SpeedyBee BLS 50A ESC, please set scale = 386 and Offset = 0.
- Power Input: 3S - 6S Lipo(Through G, BAT pins/pads from the 8-pin connector or 8-pads on the bottom side)
- 5V Output: 9 groups of 5V output, four +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 4x LED 5V pads. The total current load is 2A.
- 9V Output: 2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 2A.
- 3.3V Output: Supported. Designed for 3.3V-input receivers. Up to 500mA current load.
- 4.5V Output: Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.
- ESC Signal: M1 - M4 on bottom side and M5-M8 on front side.
- UART: 5 sets(UART1, UART2, UART3, UART4(For ESC Telemetry), UART6)
- ESC Telemetry UART: R4(UART4)
- I2C: Supported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc.
- Traditional Betaflight LED Pad: Supported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware.
- Buzzer: BZ+ and BZ- pad used for 5V Buzzer
- RSSI Input: Supported. Named as RS on the front side.
- SmartPort: Use any TX pad of UART for the SmartPort feature.
- Supported Flight Controller Firmware: BetaFlight(Default), EMUFlight, INAV
- Firmware Target Name: SPEEDYBEEF405V3
- Mounting: 30.5 x 30.5mm( 4mm hole diameter)
- Dimension: 41.6(L) x 39.4(W) x 7.8(H)mm
- Weight: 9.6g
- Firmware: BLHeli_S JH50
- Wireless Configuration: Full Configuration Supported in the SpeedyBee app
- PC Configurator Download Link: https://esc-configurator.com/
- Continuous Current: 50A * 4
- Burst Current: 55A(5S)
- TVS Protective diode: Yes
- External Capacitor: 1500uF Low ESR Capacitor(In the package)
- ESC Protocol: DSHOT300/600
- Power Input: 3-6S LiPo
- Power Output: VBAT
- Current Sensor: Support (Scale=386 Offset=0)
- Mounting: 30.5 x 30.5mm( 4mm hole diameter)
- Dimension: 45.6(L) * 44(W) * 6.1mm(H)
- Weight: 13.8g
Why Choose Phaser FPV?
Here’s Why 1000s of Buyers Trust Us
In the sky-high world of FPV drones and related products, Phaser FPV takes you higher and further – while ensuring a smooth ride every step of the way. As a human brand that puts its clients first, here are a few of the ways we keep giving our customers reasons to come back.
Same-Day Ship
If you place your order with us before 1pm weekdays, we’ll ship it out on the same day you shopped. When we make a promise, we keep it. You’ll be hard-pressed to find any Phaser order that didn’t fly out of our facility on the day it was ordered.
Transparent Stock
We keep our website updated like hawks. If you see it and it says it’s in stock, you can order it today and get it tomorrow via express shipping.
Highly Rated
We’ve spent almost a decade racking in countless 5-star reviews. Give them a read and you'll see everything we have said here is true!
Walk In Anytime
Can’t wait? Then don’t. We’re one of the only FPV drone + accessory stores to have a physical brick-and-mortar establishment in Somersby NSW Australia.
Tech Precision
Our handpicked team of technology experts specialize in – and are boffins on – every product we sell. This means they can answer any and all of your technical questions with confidence. Go ahead, put us to the test.
Fast Support
We welcome our customers to reach out to us via email, phone, or LIVE chat. Phaser FPV is the only FPV business to have a dedicated phone line.
Get Rewarded
Score a FREE gift on first and recurring orders, and discount shipping on orders over $99.
We’re on Social
We have nothing to hide. Follow us on social, tag @PhaserFPV, and become a part of our online community and family in our facebook group.
It’s clear to see why most of our business comes through word-of-mouth referrals. When you need the best in FPV & 3D Printing don’t settle for less. Demand the best – insist on Phaser FPV.