Sold Out

Pyrodrone Hyperlite F4 Race Flight Controller With VTX Pit Mode

$38.00 USD


Add to Wishlist
SKU: 11610N/A W/H N/A Categories: Drone Electronics ,

We accept the following payment methods

It's finally here!
The pyrodrone F4 board has been one of the very few boards with perfectly flat one side which lot of guys been utilizing as a "shelf" for their VTX and RX.
It was time to reroute the pads and offer a direct clean solder option for the TBS UNIFY V3 VTX and the TBS Nano RX similar to the Whitenoise Synergy FC.
The Pyro F4 RACE also has a built in socket which makes it plug & play with the Pyro32 F3 45A 4in1 ESC (The correct harness is ONLY included in the ESC package)

Please check below for tips and Betaflight Settings.

MPU6000 Gyro STM32F405 CPU @ 168mhz, can be overclocked 
2-6S direct battery input 
3.3V 100ma, 5V 2A BEC 
5V and Vbat Camera Power 
Built in configurable Betaflight OSD 
Flat bottom PCB for SUPER CLEAN builds 
36x36 PCB with 30.5x30.5 mounting holes 
UART3 (INVERTED TELEMETRY), use CLI command : Set tlm_halfduplex=off UART4 (Free), 
UART5 (Smart Audio) 
UART6 (Free)
The Pyrodrone F4 RACE flight controller can power HV VBAT or 5V Video transmitters.

Please make sure to jump the correct selection for your VTX.

If you want to use the VTX PIT mode function please type the following in the CLI command line:

resource pinio 1 A15 (Hit Enter)
Set pinio_box = 39 (Hit Enter)
Save (Hit Enter)
Assign a switch to the VTX PIT option in Betaflight MODES tab.

If VTX PIT mode is NOT needed then just solder your VTX and fly! (no additional settings needed)

If you want to solder the TBS UNIFY 5V direct to the board which is where this FC REALLY shines then here are couple tips for you.

Both the VTX and the board have "anchor" Pads on both sides of the VTX, but we do not recommend using all these anchor points for easier future maintanence in case you ever have to remove the VTX.
Here is what we recommend.
Use a very thin piece of the double sided tape that is provided in your TBS UNIFY V3 package and apply it on the VTX as shown in the below picture.
This will work as a place holder for you to line up and solder the 4 points.

When sticking the VTX to the board make sure the 4 points on the VTX (VID-AUD-GND-5V) line up with the 4 pads on the flight controller.
Once lined up solder the 4 points.

Now it's time to solder your receiver.
The board is labled for TBS NANO RX as the holes perfectly line up with the Nano RX, but you can really use any RX and just choose the correct type of receiver in the Betaflight configuration page.
Our preferred way of mounting the RX is with silicone wires rather than direct solder, Again for easier future maintenence purposes.
Please check the below picture:

Why Choose Phaser FPV?

Here’s Why 1000s of Buyers Trust Us

In the sky-high world of FPV drones and related products, Phaser FPV takes you higher and further – while ensuring a smooth ride every step of the way. As a human brand that puts its clients first, here are a few of the ways we keep giving our customers reasons to come back.

Same-Day Ship

If you place your order with us before 1pm weekdays, we’ll ship it out on the same day you shopped. When we make a promise, we keep it. You’ll be hard-pressed to find any Phaser order that didn’t fly out of our facility on the day it was ordered.

Transparent Stock

We keep our website updated like hawks. If you see it and it says it’s in stock, you can order it today and get it tomorrow via express shipping.

Highly Rated

We’ve spent almost a decade racking in countless 5-star reviews. Give them a read and you'll see everything we have said here is true!

Walk In Anytime

Can’t wait? Then don’t. We’re one of the only FPV drone + accessory stores to have a physical brick-and-mortar establishment in Somersby NSW Australia.

Fast Support

We welcome our customers to reach out to us via email, phone, or LIVE chat. Phaser FPV is the only FPV business to have a dedicated phone line.

We’re on Social

We have nothing to hide. Follow us on social, tag @PhaserFPV, and become a part of our online community and family in our facebook group.

It’s clear to see why most of our business comes through word-of-mouth referrals. When you need the best in FPV & 3D Printing don’t settle for less. Demand the best – insist on Phaser FPV.

Not enough items available. Only [max] left.
Shopping cart

Your cart is empty.

Return To Shop

Add Order Note Edit Order Note
Estimate Shipping
Add A Coupon

Estimate Shipping

Add A Coupon

Coupon code will work on checkout page