Sold Out

Seeed Studio XIAO ESP32C3 - tiny MCU board with Wi-Fi and BLE, battery charge supported, power efficiency and rich Interface

$13.00 USD

CURRENTLY IN STOCK

Add to Wishlist
SKU: 24351N/A W/H: T-05-E-12 N/A Barcode: N/A Shipping Weight: 0g N/A Categories: Raspberry Pi/Arduino , Tags: Raspberry Pi, Seeed

We accept the following payment methods

Are you looking to buy a Seeed Studio Xiao ESP32C3 Tiny MCU Board in Australia?

Seeed Studio XIAO ESP32C3 is a thumb-sized microcontroller, equipped a highly-integrated ESP32-C3 chip, built around 32-bit RISC-V operating up to 160 MHz. By 2.4GHz Wi-Fi and BLE wireless capabilities, along with low-power cost and charging ability, it provides a perfect solution for various IoT controlling scenarios and wearable device applications.

Feature

  • Outstanding RF performance:  Powerful ESP32-C3 SoC and U.FL antenna provided that supports WiFi/Bluetooth connection over 100m. 
  • Thumb-size Design: 21 x 17.5mm overall dimension, portable and lightweight. 
  • Low power consumption: Lowest as 44 μA (deep sleep mode), with 4 working modes available.
  • Onboard battery charge IC: Supports battery charging, great for various wearable scenarios and wireless IoT applications.
  • Ready for productization:  Single-sided components design, easily integrated into other boards and Seeed provides Fusion Service for rapid production.

Description

Behold, here is a new member to the Seeed Studio XIAO series, like a Thumbelina carrying a complete Wi-Fi system along with Bluetooth Low Energy function - the Seeed Studio XIAO ESP32C3 has launched!

Seeed Studio XIAO ESP32C3 has equipped a highly-integrated ESP32-C3 chip, built around 32-bit RISC-V chip processor with a four-stage pipeline that operates at up to 160 MHz. Remaining the Seeed Studio XIAO series classic form-factor of small and exquisite, it offers 2.4GHz Wi-Fi and BLE(Bluetooth Low Energy) wireless capabilities to the developers. With the addition of ultra-low-power cost and charging ability, it provides a perfect solution for various IoT controlling scenarios and complex carriable applications.

As you may see, the board equips highly-integrated ESP32-C3 SoC. The chip has been installed with a complete 2.4GHz Wi-Fi subsystem which means it supports Station mode, SoftAP mode, SoftAP & Station mode, and promiscuous mode for multiple Wi-Fi applications. It works under an ultra low power state, also supporting features of Bluetooth 5 and Bluetooth mesh. There are 400 KB SRAM & 4 MB Flash on the chip, allowing for more programming space, and bringing more possibilities to the IoT control scenarios.

Being a number to the Seeed Studio XIAO family, the board deservedly maintains the classic thumb-sized form-factor design and elegant productization single-sided components mounting. Meanwhile, it has equipped with a battery charge chip and integrated circuit for enhancing its ability to carry. This board comes included with an external antenna to increase the signal strength for wireless applications. There are 11 digital I/O that can be used as PWM pins and 4 analog i/o that can be used as ADC pins. It supports UART, IIC, and SPI serial communication ports, also including IIS (Internet Information Services). Utilizing its small and exquisite hardware design and the powerful onboard chip, programming by Arduino, it will offer more ability to wearable and portable devices or other applications. 

Seeed Studio XIAO Series Comparison

Specification

Item Seeed Studio XIAO ESP32C3
Processor ESP32-C3 SoC
RISC-V single-core 32-bit chip processor with a four-stage pipeline that operates at up to 160 MHz
Wireless Complete 2.4GHz Wi-Fi subsystem
Bluetooth 5.0/ Bluetooth mesh
On-chip Memory 400KB SRAM & 4MB Flash
Interface 1x UART, 1x IIC, 1x IIS, 1x SPI,11x GPIO(PWM), 4x ADC
1x Reset button, 1x Boot button
Dimensions 21 x 17.5mm
Power Circuit operating voltage: 3.3V@200mA
Charging current: 50mA/100mA
Input voltage (VIN): 5V
Deep Sleep Power Consumption Deep Sleep Model: >44 μA
Wi-Fi Enabled Power Consumption Active Model: <75 mA
Modem-sleep Model: <25 mA
Light-sleep Model: <4 mA
BLE Enabled Power Consumption Modem-sleep Model: <27 mA
Light-sleep Model: <10 mA

Application

  • Internet of Things
  • Wearable devices
  • Health monitoring
  • Education
  • Low-Power(LP) networking 
  • Rapid prototyping

Application 1: Smart Private Garage

Materials: XIAO ESP32C3 *2, Grove - Button *1, Grove - Relay*1

Description:

This is a peer-to-peer WiFi communication application, since two XIAOs detect each other via Wifi, the garage door will open or keep opening, and vice versa.

Improvement:

It is nice to add an ultrasonic distance sensor to measure the car-to-door distance and an OLED screen to check the status of the garage. If you want an onboard voice sensor to command the door to open with vocal instruction, try our XIAO BLE Sense. 

Application 2: Remote Forest Tracker 

Materials: XIAO ESP32C3 *1, Grove - LoRa E5 *1, Grove - GPS *1

Description:

Thanks to the tiny size of the XIAO series, it is suitable to make the wearable devices, such as a small pet tracker. This wearable device can be used as a simple GPS-Tracker which will lock its current location and publish other data via LoRa.

Improvement:

A compass that shows direction and distance is a great added value to the tracker that you could consider. Meanwhile, publishing altitude, speed, or other parameters could bring more scenarios to this tracker. Besides, the chip ESP32-C3 allows this tracker to communicate over WiFi or BLE, and therefore, we can upload the tracker’s data or realize LoRa-to-MQTT bridge as well.  

Seeed Fusion is launching a DIY XIAO Mechanical Keyboard Contest based on Seeed Studio XIAO Series! Show us your XIAO keyboard creations for a chance to win $1000 in prizes and Seeed XIAO Pillows!!! To join the contest.

Hardware Overview

Pin out overview

Component overview

Browse more

Why Choose Phaser FPV?

Here’s Why 1000s of Buyers Trust Us

In the sky-high world of FPV drones and related products, Phaser FPV takes you higher and further – while ensuring a smooth ride every step of the way. As a human brand that puts its clients first, here are a few of the ways we keep giving our customers reasons to come back.

Same-Day Ship

If you place your order with us before 1pm weekdays, we’ll ship it out on the same day you shopped. When we make a promise, we keep it. You’ll be hard-pressed to find any Phaser order that didn’t fly out of our facility on the day it was ordered.


Transparent Stock

We keep our website updated like hawks. If you see it and it says it’s in stock, you can order it today and get it tomorrow via express shipping.

Highly Rated

We’ve spent almost a decade racking in countless 5-star reviews. Give them a read and you'll see everything we have said here is true!

Walk In Anytime

Can’t wait? Then don’t. We’re one of the only FPV drone + accessory stores to have a physical brick-and-mortar establishment in Somersby NSW Australia.

Fast Support

We welcome our customers to reach out to us via email, phone, or LIVE chat. Phaser FPV is the only FPV business to have a dedicated phone line.

We’re on Social

We have nothing to hide. Follow us on social, tag @PhaserFPV, and become a part of our online community and family in our facebook group.

It’s clear to see why most of our business comes through word-of-mouth referrals. When you need the best in FPV & 3D Printing don’t settle for less. Demand the best – insist on Phaser FPV.

Sunday,Monday,Tuesday,Wednesday,Thursday,Friday,Saturday
January,February,March,April,May,June,July,August,September,October,November,December
Not enough items available. Only [max] left.
Shopping cart

Your cart is empty.

Return To Shop

Add Order Note Edit Order Note
Estimate Shipping
Add A Coupon

Estimate Shipping

Add A Coupon

Coupon code will work on checkout page